|
CAPTEURS DE DEPLACEMENT
Inductif sans contact |
|
Modèle |
Doc |
 |
The most common probe for high speed pumps
with plain metal bearings able to measure small vibration
levels and gaps up to 2mm.
- Probe Diameter: 5mm
- Operating Gap: 0 - 2mm
- Body Length: 37mm
- Thread: M8
|
EP080 |
 |
Used to measure coarser vibrations.
- Probe Diameter: 13mm
- Operating Gap: 0 - 5mm
- Body Length: 62mm
- Thread: M16
|
EP200 |
|
|
As MTN/EP200 but in low-profile mount.
- Probe Diameter: 13mm
- Operating Gap: 0 - 5mm
- Mount: Flat, three-point mounting
|
EP200F |
 |
Generally used for precision gap measurements.
- Probe Diameter: 20mm
- Operating Gap: 0 - 8.5mm
- Body Length: 75mm
- Thread: M20
|
EP340 |
 |
As MTN/EP340 but in a low-profile mount.
- Probe Diameter: 13mm
- Operating Gap: 0 - 8.5mm
- Mount: Flat, three-point mounting
|
EP340F |
 |
Widest gap capability.
- Probe Diameter: 25mm
- Operating Gap: 0 - 12mm
- Body Length: 99mm
- Thread: M30
|
EP480 |
 |
This heavy-duty eddy current probe system is
designed for the greatest protection from harsh industrial
conditions. Rugged IP65 cast aluminum driver housing with
integral probe. Stainless steel probe sleeve tailored to
exact insertion depth required and the probe can be
exchanged without recalibration. Unit can be based on any
driver type highlighted in this guide. Particularly suited
to thrust or vibration measurements on pumps and turbines.
- Probe Diameter: 5mm
- Operating Gap: 0 - 2mm
- Insertion Length: As required
- Protection: IP65
- Entry: M20
|
EPHD080 |
 |
Voltage output driver suitable for
conventional +24VDC power supplies.
- Output: 0 – 16V proportional
- Power: +24VDC
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
MTN/ECPD 24V |
|
|
Voltage output driver for negative going
power supply required to match other manufacturers’
controllers.
- Output: 0 – 16V proportional to probe
gap
- Power: -24VDC
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
MTN/ECPD -24V |
|
|
Voltage output driver suitable for
conventional +24VDC power supplies. Lower output sensitivity.
- Output: 0 – 10V proportional to probe
gap
- Power: -24VDC
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
MTN/ECPD/78 |
 |
Current output driver for gap measurements.
Range dependent on associated probe, typically 2mm gap for
thrust measurements on turbine and pump shafts. Three-wire
configuration.
- Output: 4 – 20mA proportional to
probe gap
- Power: -24VDC, three-wire loop-powered
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
MTN/ECPD60 |
|
|
Current output driver for vibration
measurements. Range dependent on associated probe, typically
125micron peak-to-peak vibration for turbine and pump shafts.
Three-wire configuration.
- Output: 4 – 20mA proportional to
vibration
- Power: +24VDC, three-wire loop-powered
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
|
|
|
Current output driver for gap measurements.
Range dependent on associated probe, typically 2mm gap for
thrust measurements on turbine and pump shafts. Loop-powered.
- Output: 4 – 20mA proportional to
probe gap
- Power: +24VDC, two-wire
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
|
|
|
Current output driver for vibration
measurements. Range dependent on associated probe, typically
125micron peak-to-peak vibration for turbine and pump shafts.
Loop-powered.
- Output: 4 – 20mA proportional to
vibration
- Power: +24VDC, two-wire
- Probe Connection: SMC
- Enclosure: Powder coated die-cast
alloy
|
|
